Thyro-A is an international registered trademark of AEG Power. Solutions GmbH. Windows and Windows NT are registered trademarks of the Microsoft. The Thyro-A is a communication-capable Thyristor Power Controller. synchronization option (in TAKT operating mode with Thyro-Power Manager option) and. These operating instructions are part of the Power Controller Thyro-A. . change parts not approved by AEG SVS as well as any other use of Thyro-A is not.

Author: Shaktigis Samulkree
Country: Peru
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 September 2016
Pages: 107
PDF File Size: 2.14 Mb
ePub File Size: 14.3 Mb
ISBN: 599-2-14536-560-8
Downloads: 81615
Price: Free* [*Free Regsitration Required]
Uploader: Kazralmaran

The contents are not subject matter of the contract, but serve only as information.

Thyristor Power Controller Thyro-A – BG electric e.K.

Different variations can be realized depending on the requirements. Skip to main content. Calculate Varies based on location and shipping method. These operating instructions correspond to the technical state of Thyro-A at the time of publication. It is to advise the product user and protect him and his systems. This makes staggered switching possible, particularly with the slow pulse time of 1 sec.

This amount is subject to change until you make payment. The warranty obligation of the manufacturer applies only if these operating instructions are observed. Further information is available on this in chapter 3.

Die arg regionalen Adressen finden Sie im Internet: Heating up of the device by heat sources must be avoided. If a different operating mode is desired, then it must be set by the user. With the last controller X2. The item may be missing the original packaging, or in the original packaging but not sealed. The dissipation of the Power Controller is fhyro-a in the Type overview table.


Back to home page. In order to achieve a narrower line width with a line recorder the output signal can be smoothed as required.

Do they have something to sell?


Seller assumes all responsibility for this listing. All values are available through the bus module. Within the stated input ranges these aey with the control characteristic may be adjusted to any common signal characteristic. If low load currents are required, check if a controller with a lower type current can be used. Additional information and notes for unqualified persons and for the use of Thyro-A outside of industrial installations are not contained in these operating instructions.

The selectable signal levels are V, mA, mA. The item you’ve selected was not added to your cart.

AEG Thyro-A 3A HRLP1 Thyristor Power Controller | eBay

An error occurred, please try again. Depending on AN1 the soft start time has the following value: There is no product norm for Thyristor Power Controllers so that a sensible norm structure must be set up which ensures safe application and opportunity for comparison. This item will ship to United Statesbut the seller has not specified shipping options. Please use eBay messaging system.

Connection Prior to connection, it must be ensured that the voltage information on the type plate corresponds with the mains voltage. It’s a community-based project which helps to repair anything.


Please observe the operating instructions of the SYT-9 component. The value is set by potentiometer R Synchronization voltage is supplied to X1. The following signal ranges can be set: This work is only to be carried out by a skilled electrician. Contact the seller – opens in a new window or tab and request a shipping method to your location.

Seller information harpoonplc Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab. If a poti is changed, this is recognised by the Thyro-A. Depending on the prescribed set point, mains half waves are switched.

The distance between the Power Controller and the cabinet ceiling or other mountings should be at least mm. The item may be a factory second or a new, unused item with defects.

The responsibility for the necessary measures to avoid hazards to persons and property is borne by the operator or the user. Should there be a flicker, this can be minimized with the aid of the mains load optimization. With the first connected controller the SYT input X2.


Shipping cost cannot be calculated. If required, the control device can additionally be supplied with 24V a. With set point full modulation 20mA, 10V, 5V see 3.