Danfoss Drives regarding PELV .. acteristics of the installation, since Danfoss VLT Max. motor cable length, screened cable VLT V. Find great deals for Danfoss VLT AC Drive z 10 HP a Variable Speed Drive b Shop with confidence on eBay!. Find great deals for Danfoss VLT AC Drive Z 10hp. Shop with confidence on eBay!.
|Published (Last):||2 November 2007|
|PDF File Size:||2.64 Mb|
|ePub File Size:||20.51 Mb|
|Price:||Free* [*Free Regsitration Required]|
Display Mode I The table below gives the operating data options for the first and Line 4 is the status line and the information is automatically generated second lines of the display. To print the manual completely, please, download it. For a read command, the index must have the following format: Rated current Parameter to rated current The warning functions in parameters through are not active during ramp-up after a Start command, ramp down after a Stop Function: Reference Handling It is possible to have dantoss internal preset references and external references at the same time.
The first error code index  in parameter vvlt, Error code, must be read. Remove the cover with a parameter settings. This parameter is used for setting the signal value that corresponds to This parameter is used to set the signal value that corresponds to the the minimum reference or the minimum feedback, parameterminimum reference value or the minimum feedback, parameterGeneral 25 inches mm front space for access.
Danfoss VLT 6011 AC Drive 175z7360 10 HP 30.0a Variable Speed Drive 174b5218
Application Functions – Parameters Through Description of choice: Connecting input power to motor terminals will Vot entry must be from the bottom on all drives. The pulse rate is set by parameterTerminal 45, Output, Pulse Scaling. Warning Functions Warning Functions Warning: Page 4 VLT Start-up Connection Examples Connection Examples: The serial communication on the communication option card is not working.
This value can be reset using parameterReset of kWh Counter. All drives except VLTto V and VLTThe shield of the control wires vlh be grounded at the cable clamp at to V must be mounted directly to the wall with no spacers.
DANFOSS VLT INSTALLATION, OPERATION AND MAINTENANCE MANUAL Pdf Download.
ddanfoss Warnings and Alarms In addition, an automatic reset may be selected in parameterReset Function which will reset all non-trip lock faults. If there is more than one warning or alarm, the sum of the warnings or alarms will be shown. By pressing ‘print’ button you will print only current page.
See also parameters throughDisplay Terminal 54, Analog Input [V], parametergives the voltage value Readout. Page 43 Description of vl The unit for the reference can be seen from the following table: Programming Programming Operation and Display Parameters through Using the Extend Menu key, it is possible to access to all the parameters for the drive. If used as an analog Warning: If Danfoss FC protocol is danfoas be selected, set parameterProtocol to Only a slave that has received a faultless packet addressed to that FC protocol.
Reference Type The example below shows how the resulting reference is calculated when Preset references are used together with Sum and Relative danffoss set in parameterReference Type. Parameter to parameterMaximum Frequency Switching frequencies higher than 4. Calculation Of Resulting Reference Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum vlr references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.
Programming Operation and Display Parameters through Using the Extend Menu key, it is possible to access to all the parameters for the drive. All terminals for the low voltage control wires are located under the Many of these terminals have multiple functions determined by protective cover below the keypad.
Calculation of Resulting Reference The calculation made below gives the resulting reference when External reference is the sum of references from terminals 53, 54, parameterReference Type, is programmed for Sum and Relative, 60 and serial communication.
Danfoss VLT 6002-6011 Installation, Operation And Maintenance Manual
DC link voltage [V] is the drive DC bus voltage. Input Fuses These fuses may be specified as an option to the drive and mended fuse rating. Conduit entries are result in drive failure when power is applied. Inputs and Outputs Parameters through In this parameter group, the functions of the drive input and output terminals are defined.
The status word is used to inform the master e. In this Display Mode key is pressed and held.
This parameter makes it possible to see the reason why a fault trip occurs. Activate sleep mode in parameterSleep Mode Timer.