INTECONT TERSUS MANUAL PDF

Intecont Tersus – Free download as PDF File .pdf), Text File .txt) or read for weighing tasks better than % Manual and/or automatic zero setting Full. The INTECONT Tersus weighing elec- tronics is specially tion module, INTECONT Tersus optimally fits into any Manual and/or automatic zero setting. processes, the INTECONT Tersus meas- uring, control, and supervisory module, INTECONT Tersus optimally fits into any Manual and automatic zero setting.

Author: Aralabar Motaur
Country: Hungary
Language: English (Spanish)
Genre: Video
Published (Last): 10 August 2012
Pages: 432
PDF File Size: 10.11 Mb
ePub File Size: 3.82 Mb
ISBN: 573-9-33074-818-9
Downloads: 62026
Price: Free* [*Free Regsitration Required]
Uploader: Nilrajas

Load cell usage factor jntecont approx. Disconnect load cell connector X7 and plug in the test connector instead The dimensioned resistances given result in the following service values: This is done by loading the weighing plat-form with a known calibration weight and automatically calculating the average platform load over one or several whole belt circuits.

The control or readjustment can take place using two different me-thods.

Zero manuao should be started manually at regular intervals if automatic operation is not preselected. The following two lines show readings that can be selected with the cursor buttons. Volumetric Synchronous In contrast to volumetric operation, it is not the rated belt load that is used for calculating the set belt speed.

Preselection batching mode Preselecting the batching mode makes batching possible, although it does not initiate a batch. It only shows the functions that can be called up now. Memory A P No entry can be made if batch mode is deselected or if a batch is in process.

  CLOSET WARDROBES DESIGN FILETYPE PDF

PersonnelPersonnelPersonnelPersonnel Preparation, assembly, commissioning, operation, maintenance and servicing may only be carried out by qualified personnel.

The batching process can be controlled via the belt conveyor drive or via the bin feeder. This increases the scale’s short-term accuracy. For example, the evaluation electronics for continuous measurement systems are ideally equipped for international use.

Input the value Acknowledge input.

That substantially boosts mnaual short-term accuracy of the scale. The password is queried once the function has been called up. The external setpoint will be taken if the source is switched from an external source to the keyboard OP. Display warning 2 Fig.

Manual Intecont Tersus

Reset the totalizing counter The function has to be activated with the P The feed rate will continue being calcu-lated for the time set in P Dialog language, display units and availability or security of the function block functions.

Poten-tial hazards may then arise from e. This would change the timing of calibration programs. During office hours, service specialists from all divisions are on hand to analyze problems and failures.

Parameter block Calibration Data: Secure them against inadvertent restart. The inclination of the belt may only be entered for systems in which the load cells are arranged perpendicular to the belt. Zero setting takes place with an empty belt conveyor with a program which runs automatically. It continues with intecotn set-up operating menus, automatic adjustment programs, integrated weighing applications and calibration memory for conveyor belt scales.

  DEUTSCHLAND TESTET COUPON PDF

They adapt their font size over 3 levels.

Manual Intecont Tersus

Belt load measurement is turned off. Entries might be missing de-pending upon this setting. Subject to change without prior notice.

The set and actual feed rates are compared and the difference conducted to the controller. VeVeVeVertical to the belt conveyorrtical to the belt conveyorrtical to the belt conveyorrtical to the belt conveyor 0 must be entered as angle a. Take appropriate action to ensure that the measuring sys-tem cannot be inadvertently restarted.

After taring, the total remains unchanged over one belt circuit with the empty belt. It is determined by the design of the weighing platform and can usually be found in the technical data sheets.

No special measuring sensors are required to do this. If there is no manuao, memorize the value and report to Schenck Process. However, it is always expe-dient to measure the length manually and to enter the exact value as a parameter.

Belt Speed 3 s P