INTERSEAL 211 PDF

With the patented dry®, interseal has developed a technically and . 8 x 8 x microns ( mils) dry equivalent to. microns ( mils) wet . Interseal Interthane SYSTEMS. COMPATIBILITY. Sep 22 , , SYNTHETIC ENAMEL PAINT, INTERSEAL HSALUMINIUM PART A EGA/20LT, Sri Lanka, Bangalore, LTR, , 35,,

Author: Meztik Jushura
Country: Austria
Language: English (Spanish)
Genre: Relationship
Published (Last): 17 July 2006
Pages: 155
PDF File Size: 1.56 Mb
ePub File Size: 15.66 Mb
ISBN: 830-1-68135-455-7
Downloads: 28437
Price: Free* [*Free Regsitration Required]
Uploader: Akinozil

Consult International Protective Coatings for further details. A low VOC, two component high build, high solids surface tolerant epoxy maintenance coating. A two component, low VOC, high solids epoxy, pigmented with aluminium to provide enhanced corrosion resistance. As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.

Always mix a complete unit in the proportions supplied. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.

Press and move to zoom.

Export Data and Price of paint interseal hs from Bangalore | Zauba

A high solids, low VOC, two component, high build, surface tolerant epoxy coating, Interseal HS provides excellent anticorrosive protection in industrial and offshore environments in both atmospheric exposure and immersion service. Once the unit has been mixed, it must be used within the working pot life specified. Interseal HS is suitable for application to a wide range of substrates and aged coatings.

Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. Mouse over image to zoom. Prior to paint application, all surfaces should be assessed and treated in accordance with ISO The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits.

Thoroughly flush all equipment with International GTA Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions.

  IRFP044N DATASHEET PDF

A single component, spray applied, high build, water based coating for direct application over coated substrates and non-ferrous substrates. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.

Interseal | Protective – Coatings – AkzoNobel

It is good working practice to periodically flush out spray equipment during the course of the working day. A two component, low VOC, high solids, fast curing anticorrosive epoxy primer. Provides quick cure even at low temperatures often encountered in maintenance painting. VOC values are typical and are provided for guidance purpose only. However, if necessary, application over prefabrication blast primers can 21 performed.

This product is not available in pale and pastel shades due to a tendency to discolour rapidly. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. At low temperatures, it may be necessary to thin Intercure HS to enable airless apray application to be performed. Number of Components Multi pack 4 Single Pack 2. Additionally, in common with all epoxies Intercure HS will chalk on exterior exposure.

Low Interweal Curing 24 Hours 1. Available in colours as well as aluminium and glass flake versions with passivator, to provide additional anti-corrosive barrier protection.

Absolute measured adhesion of topcoats to aged Intercure HS is less than that to fresh material, however, it is adequate for the specified end use. Interseal dries to form a non-tacky, tough, resilient temporary protective layer. Excessive over application of material on areas such as poorly prepared welds may result in long term stress cracking and so early failure.

However, these phenomena are not detrimental to anti-corrosive performance. This product must only be thinned using recommended International GTA thinners.

Systems compatibility Intercure HS will normally be applied to suitably prepared steel, e. Zinc Phosphate version also available. If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard. Be the first to write a review for this product! Product Type Primer Chemistry Epoxy. Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops.

  EL MANUSCRITO VOYNICH DESCARGAR PDF

Search Import Export Data of India

Varnish Hybrid Water base. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.

Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed to deteriorate under good shop conditions onterseal up to days.

The use of alternative thinners, particularly those containing ketones, can severely inhibit the curing mechanism of the coating. Surface preparation All surfaces to be coated should be clean, dry and free from contamination. If the shop primer shows extensive or widely scattered breakdown overall sweep blasting maybe necessary.

INTERCURE 200HS – PART B – 3.79L

Low molecular weight reactive additives, which will form part of the film during normal ambient cure conditions, will also effect VOC values determined using EPA Method GTA Do not thin more than allowed by local environmental legislation Mix ratio: Dry time 1 Hours 1 26 Hours 1 48 Hours 1 8 Hours 1. Intercure HS can also be used as a primer for substrates other than ingerseal steel, e. Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties.

Product Line Interseal 6.

Work stoppages Do not allow material to remain in hoses, gun or spray equipment. Over-application should be avoided as thick films will not be as good a substrate for topcoat adhesion after ageing as those at the specified thickness.