KEMA 08 ATEX 0110 PDF

KEMA 08 ATEX IECEx KEM Features. □ Wide temperature range . □ PLEXO connection system, cold-applied connection and shrinkable tubing. EU-Type Examination Certificate Number: KEMA 98ATEX X are recorded in confidential test report number NL/KEM/ExTR/ KEMA 05ATEX X. PTB 02 ATEX X. Electrical KEMA 08ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX SEV 10 ATEX.

Author: Kimi Akihn
Country: Togo
Language: English (Spanish)
Genre: Software
Published (Last): 22 July 2010
Pages: 144
PDF File Size: 7.39 Mb
ePub File Size: 7.21 Mb
ISBN: 408-7-13198-566-4
Downloads: 14445
Price: Free* [*Free Regsitration Required]
Uploader: Nenris

Junction boxes for Pt Ex, The heating tape is cut and terminated directly on the construction site according to the circumstances.

kema 08 atex pdf – P(1) –

Fixing method Large-area heaters can be installed with self-adhesive tape, with a special glue, by means of a clamping plate or tension springs. This thermostat can be used to regulate internal temperatures of switch and control cabinets, transmitter protection boxes, measuring equipment etc. The ksma here is that the actual values and states can be read comfortably and safely on the large LCD displays. System calibration is not necessary. This self-limiting property prevents overheating even when the tapes are crossed.

The outer insulation jacket is made of fluoropolymer for special applications which require chemical resistance and mechanical strength. For special applications which require chemical resistance and mechanical strength a 01110 insulation-jacket is optionally available.

Thanks to the parallel design the heating tape can be cut and installed to any required length.

  BEDRIJFSBESLISSINGEN EN FINANCIELE VERANTWOORDING PDF

BARTEC Documentations

Thanks to the pliable part of the resistance thermometer, the device is excellently suitable for application areas requiring a high degree of flexibility and replaceability e.

Alarms are given if values exceed or fall below the pre-defined load or leakage-current limits.

Statistical data on lema current and energy consumption are determined by means of the integrated data logger. After a temperature drop of 5 K below the limit set point, or after a fault has been remedied, the limiter can be re-activated by means of a re-set button on the device itself or via a remote re-set control.

Technical data | Heating Technology

Installation kit explosion protected set fold set Order no. If there are deviations, the taex relays are triggered accordingly. The use of these heater plates guarantees a maximum degree of operational safety, as temperature fluctuations can be efficiently avoided and, yet, the required minimum temperatures can be maintained. This light plastic-sheathed cable is filled afex magnesium oxide.

In order to prevent accumulation of heat the specified fitting distances must be observed. The MPC II is available in three different versions to meet the requirements of a wide variety of applications and tasks. The limiter function can be suppressed by a digital input when carrying out servicing work on the heating circuit, e. The pliable part of the resistance thermometer starts after 50 mm. The PA00 touch panel serves as the interface here. The power output controller works in interference free full wave control mode by means of a semiconductor relay.

  JEAN ROUCH CINE ETHNOGRAPHY PDF

If there is a rupture or break ke,a the sensor tube leakagethen the switch remains permanently open fail-safe. You can choose between 3 different EKL heating cable systems: The special design of the aluminum profile facilitates an even temperature distribution in the interior of housings and cabinets.

The thermostat can be installed either over the mounting hole with M6 thread or with the M20 connecting thread. Periodical assessment is to be performed after 2 kemaa and after 3. The heating circuit end is closed kems each case with a heat shrinkable end cap.

A bimetallic switch integrated in the terminal block limits the surface temperature of the heater approx.

Cable thermostat KTE-m, B It is also used to actuate the external contactor for switching the heating circuits. If desired, the autotuning function will automatically determine the optimum PID adjusting parameters for the control path. Maintenance work of future modifications of the heating circuit can be carried out more efficiently.

Structure All functional 01100 are integrated in a standard Ex e aluminium enclosure.

If the tape will be damaged, it is not necessary to replace the whole tape.